Menvier Security TS700 Instruction Manual download pdf (Page 19)

Key Display Attri bute Type

Acc

Access - Circuits programmed with this attribute are automatically isolated during the

en try procedure to allow a "walk through" route for the user to access the remote keypad.

Whenthe system isparts etactivationof a circui t withthe "Access"attribute willstartthe entry

timer. The Access attribute may only be assigned to Night circui t types.

2AcT

Double Knock - Circuits programmed with this attribute will only cause an alarm if:

a) Thec ircuitisactivatedtwicewithintheDouble K nockwindow(thistimemaybe setinthe

System Timers menu).

b) The circuit remains active for the whole duration of the Double Knock window.

The Double K nockattribute mayonlybeassignedtoNight,24hrandAuxiliarycircuittypes.

TEST

Test - Circuits with this attribute wi ll be disabled fr om the system for the period set by the

"Test Ti me" (s ee System Timers).If the circuit is activated during this period the activation w ill

be logged and the user is inform ed of the circui t failure when trying to set the system. The

testfailmessagemayonlybe clear edwiththe engineer's p asscode.Ifat theendofth e test

period no activations have occurred the circuit is automatically r emoved from test and

behavesas normal.Thetestperiod is initiatedbyenteringt heengineer's passcode. Thetest

attribute may only beassigned to Night, 24hr, PA Silent , PA Audible, Fire and Auxiliarycircuit

types.

ISOL

Isolate - Circuits with th is attribute are allowed to be omitted by the user when setting the

system.The isolate attributemayonlybeassignedtoNight,24hrandAuxiliarycircuittypes.

RST

Reset - This a ttribute is normally assigned to a circuit that is connected to a Vibra tion or

Smoke d etector, so that during the "Detector Reset" period the circuitis not monitored. The

Re set attribute may only be assigned to Night, 24hr, Fire an d Auxiliary circuit types.

Ta ble 4. Circuit Attributes

System Timers

There are ten separate system timers which are sh own in Table 5a and 5b.

1. Ensure that "Engineer Menu 1 " is selected .

2. Press 5 to select the System Timers option.

3. The display will show: Tir.-

4. Enter the required timer number 0 to 9.

5. The display will show the current timer setting.

6. Enter the new timer value an d pr ess [.

7. The display will return to step 3. Repeat steps 4 to 7 for the

remaining outputs.

8. Press ] to return to "Engineer Menu 1".

Key Timer Range Function

ACPO Delay 0-199sec ForACPO requirementsthistimerisnormallysetto 90 seconds.Ifduringthe

en try procedure the user deviates from the e ntry route and causes an

alarm, the communication of the alarm signal to the central station is

delayed by this timer .

Re -Arms 0-199 At the end o f the bell durat ion time the sy stem re-arms all circuits that are

he althy. Circuits thatarestillin an alarm areisolated u ntiltheychange to a

he althy condition. This timer controls the number of times that a circuit will

re-arm before it is locked out of the system.

Ta ble 5a. System Timers

TS700 Installation Manual Programming

Tir.-

Ent er timer number 0 - 9. (see

Table 5a & 5b)

030

Ent er timer value 000 -199. (see

Table 5a & 5b)

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 31 32

Comments to this Manuals

No comments

Menvier Security TS700 Instruction Manual Page 19

Comments to this Manuals

Related products and manuals for Security access control systems Menvier Security TS700