Menvier Security TS900+ Specifications download pdf (Page 28)

No/Type Description

041

Time Switch B

This output is controlled by the settings of

“Time Switch B” (see Engineers Menu 3)

042

Time Switch C

This output is controlled by the settings of

“Time Switch C” (see Engineers Menu 3)

043

Access Code

Activates when an “Access” passcode

is entered. The duration of this output is

controlled by the setting of the

“Acc.CODE DUR” timer (see System

Timers).

044

General Fault

Activates during battery fault or when

the system is prevented from being set.

Deactivates when all faults are

cleared.

045

Battery Test

Activates for 1 minute on the hour every

hour. This output is used to test the

battery in remote PSU using a 519FM

monitor PCB).

046

Service Call

Activates when the system is on-line

with a remote PC and Lineload

software.

047

System Full Set

Activates when all areas within the

system are set and deactivates when

any area is unset.

048

Custom O/P A

This output is active when a

combination of output conditions

occur. The combinations are

programmed in Engineers Menu 3 (see

page 47).

049

Custom O/P B

This output is active when a

combination of output conditions

occur. The combinations are

programmed in Engineers Menu 3 (see

page 47).

050

PC output 1

This output can be switched on or off

via the PC and “Lineload” software.

051

PC output 2

This output can be switched on or off

via the PC and “Lineload” software.

052

Sounder Control

Normally used as the 0V connection

for an extension loudspeaker so that

only system alarm tones are

generated. Only suitable for Panel

Outputs 1 and 2.

053

Service Required

Activates when the “SERVICE

REQUIRED” message is displayed and

deactivates when the engineer

passcode is entered.

054

Call Engineer

Activates when the system requires an

“Engineer Reset”, deactivates when

the system is reset by the engineer or

“Remote Reset”.

055

Always Off

Never activates.

056

Duress

Activates when a duress passcode is

entered and deactivates when the

duress alarm is reset.

No/Type Description

057

System Part Set

Activates when the system is part set,

deactivates when the system is fully

unset or fully set.

058

Battery Fault

Activates when a battery fault occurs

and deactivates when the battery fault

is cleared.

059

Set Fail

Activates when any ward fails to set,

deactivates when the set fail condition

is reset.

060

Open/Close

Activates when the system is unset,

deactivates when the system is

set/part-set.

061

ID Alarm

Activates for 2 seconds when any

circuit causes a new alarm condition.

062

Random

Activates randomly (min = 5 minutes,

max =60 minutes)

063

Modem lockout

Activates when the modem is

locked-out (four failed attempts).

Deactivates when a master user

passcode is entered or after 4 hours.

064

Sndr Control A

Activates when “Ward A” is in entry, exit,

alarm or set fail.

065

Sndr Control B

Activates when “Ward B” is in entry, exit,

alarm or set fail.

066

Sndr Control C

Activates when “Ward C” is in entry, exit,

alarm or set fail.

067

Sndr Control S

Activates when “Ward S” is in entry, exit,

alarm or set fail.

068

Chime

Activates for 2 seconds when a circuit

that is programmed as “chime” is

activated.

069

24hr Ccts Omit

Activates when one or more 24 Hour

circuits are omitted.

070

Timed Output

Activates when a “Monitored” circuit is

triggered and remains active for the

duration of the “Monitor Dur" see

System Timers.

071

Abort

Activates for 5 seconds after an alarm

is aborted by the user. The period in

which the alarm may be aborted is set

by the “Abort Delay” see System Timers.

100 - 155

Circuit Mimics

Will mimic (active when circuit is

active) circuits 01 to 56 respectively

200 - 255

Circuit Alarms

Active when a circuit causes an alarm,

for circuits 01 to 56 respectively .

Engineer’s Menu 1 TS790 & TS900 Installation Manual

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 67 68

Comments to this Manuals

No comments

Menvier Security TS900+ Specifications Page 28

Comments to this Manuals

Related products and manuals for Security access control systems Menvier Security TS900+