Menvier Security SD1 Instruction Manual download pdf (Page 16)

Exit Time

This timer sets the delay between the user initiating

the setting procedure and the system actually

setting. This only applies when the system is

programmed to set by "Timed Exit", see "System

Options" on page 17.

➤

Toprogramtheexittimeproceedasfollows:

1. Ensure that the engineer’s menu is selected,

then press [4] to select Exit Time.

2. Selecttherequiredexittimebyusingkeys[1] to

[4] to light the appropriate zone LED.Whenthe

LED is lit the exit time will be as shown below:

Zone LED LED On

Zone 1 10 Seconds

Zone 2 30 Seconds

Zone 3 1 Minute

Zone 4 2 Minutes

3. When completed, press [0] to accept, a high

pitched acceptance tone will be heard and

the system returns to the engineer’s menu.

Entry Time

When the entry procedure is initiated, the Entry

Timer is started. If a valid user passcode is not

entered when the timer reaches zero, a full alarm

tone is generated from the internal sounders only

and the timer is restarted. If a valid user passcode

is not entered when the timer reaches zero for the

second time the external sounder is activated.

➤

Toprogramtheentrytimeproceedasfollows:

1. Ensure that the engineer’s menu is selected,

then press [5] to select entry time.

2. Selecttherequiredexittimebyusingkeys[1] to

[4] to light the appropriate zone LED.Whenthe

LEDislittheentrytimewillbeasshownbelow:

Zone LED LED On

Zone 1 10 Seconds

Zone 2 30 Seconds

Zone 3 1 Minute

Zone 4 2 Minutes

3. When completed, press [0] to accept, a high

pitched acceptance tone will be heard and

the system returns to the engineer’s menu.

Bell Duration Time

This timer controls the duration of the external

sounder when the system is triggered into a full

alarm condition.

➤

Toprogramthebelldurationtimeproceedas

follows:

1. Ensure that the engineer’s menu is selected,

thenpress[6] toselectthebelldurationtime.

2. Select the required bell duration time by using

keys [1] to [4] to light the appropriate zone

LED.WhentheLEDislitthebelldurationtimewill

be as shown below:

Zone LED LED On

Zone 1 90 Seconds

Zone 2 3 Minutes

Zone 3 10 Minute

Zone 4 20 Minutes

Zone 5 Continuous

3. When completed, press [0] to accept, a high

pitched acceptance tone will be heard and

the system returns to the engineer’s menu.

Change Engineer’s Passcode

The factory default engineer’s passcode is set to

[1] [2] [3] [4], but the installation engineer should

changethistotheirownpersonal4digitpasscode

as follows:

➤

Tochangetheengineer'spasscodeproceed

as follows:

1. Ensure that the engineer’s menu is selected,

then press [7] to select change engineer’s

passcode.

2. Zone LEDs 1 to 4 will now light.

3. As the new passcode is entered each LED will

go out one by one. When all 4 digits have

been entered, LEDs 1 to 4 will light again and

the new passcode must be re-entered for

confirmation.

4. A high pitched tone indicates the new

passcode was accepted, a low pitched tone

indicates the passcode was not accepted. If

the passcode was not accepted repeat the

procedureagain,usingadifferentpasscode.

Programming TS400/TS410 Installation Instructions

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Comments to this Manuals

No comments

Menvier Security SD1 Instruction Manual Page 16

Comments to this Manuals